What's New?
Activity Stream
New Posts
New Group Messages
New Events
New Articles
New Blog Entries
Mark Forums Read
Articles
Forum
Blogs
Log in
Remember Me?
Forgot your password?
Home
Activity Stream
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 24 Hours
Last 24 Hours
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Articles
Articles
Blog
Blogs
Groups
Groups
Filter by:
Last 7 Days
Clear All
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
Today,
07:52 AM
mr_es335
replied to a thread
About the TCP-Master/Slave!
in
SAWStudio
Goran, If you really want to take such to a new level, have a look-see at Vienna Ensemble PRO
see more
1 replies | 28 view(s)
Today,
03:10 AM
Göran Nordberg
started a thread
About the TCP-Master/Slave!
in
SAWStudio
Hello Folks! First time use of the TCP-finesse Master/Slave. This is...I mean this is sooo aaaamaaaziiing, this opens up to a whole new world,...
see more
1 replies | 28 view(s)
Yesterday,
11:21 PM
cgrafx
replied to a thread
OT: mixing unblanced gear in a balanced patch bay
in
SAWStudio
Will depend on the patch bay, but if it's a wire soldered to the back, then you would specifically wire as TS, not TRS. Also you'll need to know if...
see more
7 replies | 68 view(s)
Yesterday,
11:11 PM
Dave Labrecque
replied to a thread
OT: mixing unblanced gear in a balanced patch bay
in
SAWStudio
Thanks for the link. Good stuff. What do you mean by "wire the patch bay connectors with the correct wiring for the unbalanced equipment"? The...
see more
7 replies | 68 view(s)
Yesterday,
10:47 PM
Dave Labrecque
replied to a thread
OT: mixing unblanced gear in a balanced patch bay
in
SAWStudio
I'm not worried about noise getting into unbalanced runs so much, just want to be sure the sound gets through cleanly. In all typical normaling...
see more
7 replies | 68 view(s)
Yesterday,
04:06 PM
jmh
replied to a thread
OT: mixing unblanced gear in a balanced patch bay
in
SAWStudio
You might be able to just leave everything wired as balanced to and from the patchbay then you could use a t-s patch cable to bridge between the...
see more
7 replies | 68 view(s)
Yesterday,
03:37 PM
cgrafx
replied to a thread
Ins and Outs on Different Soundcards??
in
SAC
The Dante Virtual sound card driver may have too much latency to use for monitor mixes (although they do say 4, 6, or 10ms). The question is going to...
see more
2 replies | 30 view(s)
Yesterday,
03:09 PM
John F
replied to a thread
Ins and Outs on Different Soundcards??
in
SAC
I might have just answered my own question. I'll bet I use the Dante soundcard and assign my monitor speakers as outputs from the Dante-enabled...
see more
2 replies | 30 view(s)
Yesterday,
03:03 PM
John F
started a thread
Ins and Outs on Different Soundcards??
in
SAC
My church is purchasing a new sound system, and we'll be using SAC for the webstream part of it. I've just run into an issue I didn't think about -...
see more
2 replies | 30 view(s)
Yesterday,
10:45 AM
cgrafx
replied to a thread
OT: mixing unblanced gear in a balanced patch bay
in
SAWStudio
here is a really good article with diagrams https://www.ranecommercial.com/kb_article.php?article=2107 The most critical issue is going to be...
see more
7 replies | 68 view(s)
More Activity
No More Results
No Recent Activity
Connect With Us