Go to that mixer and clear the name... leave it blank... then re-enter the name you want on FOH and it should track down again.

Bob L

Pay attention to the MT Load and Src Load readouts during playback... see what the numbers are... a high MT load suggests heavy processing loads... plugins possibly causing this... high src loads...

OK... I was able to understand what you meant and was able to find a quick fix for the miscalculation.

There is a new version 1.3 already up for download.

Good detective work guys.

Thanx.
...

A quick fix.

Bob L


Version 1.3
Enhancements
*

Bug Fixes

Not sure about Dave's files... but I just ran another test here on a session. Take a 32 bit session in SAWStudio32 and build a mix. Open the exact same session in SAWStudio64... build a mix to...

When working with video... make sure to install the KLite codec pack... then SAW will easily recognize and handle all kinds of MP4 and Divx and Xvid... etc.

Bob L

Windows will pad files on disk... perhaps this is all that is happening... note that disk size and filesize are reported as two different values on every disk file in properties.

I have not...

I'll explore into it... although this is the first reported case of a problem and there have been many thousands of wav files created in SAWStudio64... so I am not sure.

Bob L

With Zoom... you might simply take the audio out of SAC and physically connect with a cable back into the line in of the motherboard soundcard and let zoom use that audio... works well.

Bob L

I would suggest using the Control Track in the MultiTrack.... open that view and simply place your cursor at a particular measure and the use the built-in command list to send a midi program change...

Names should transfer down when entered from the FOH mixer or Monitor Mixer 1 (as a master Mon Mixer)... names entered on Mon mixers 2-24 will remain independent on each mixer.

Bob L

Consider using Drumagog to re-trigger the toms with tom samples and mixing that in with the original toms or replacing the originals if there is too much leakage.

Bob L

There is a reported issue with meters stopping after the engine has been on for more than around 24 hours... stopping and restarting the engine fixes it... I have tried to chase this down, but it is...

Make sure the Meter Active options in the Mixer menu are checked.

Bob L

Use the .ini file vst method to point to the vst plugins that are in SAW and they will show up in SAC... the info is in the helpfile.

Setup all your inputs in SAC and then use the Import SAC Data...

After a fresh SAWStudio install, you just need to run it once to establish all the default paths that the program creates... then you can exit and install the midi workshop which is dependent on some...

In SAWStudio aux send/ret the signal should be in phase... I was thinking SAC with that statement, which does not attempt any latency compensation.

Bob L

Yes... I thought about a forced reset everytime the engine stops... I may have to implement that option to compensate.

Bob L

Yup... nobody seemed to care.... they say the problem is with my software.

Oh well.

Bob L

I've noticed that the Dante hardware audio card drivers actually unload the driver memory when the audio engine is stopped... as if the program was shutting down... anoying... you have to reset the...

In SAC, you can route from any out to any in... but you will suffer extra latency... the aux send / return in SAWStudio compensates for the latency.

Bob L

Its pretty simple really... use an aux send and return combination... go to one of the aux returns and on the master aux Out asignment pick one of your device outputs... then patch cables to your...

If you use the PER-MON user rights, that user can only control his own mixer and will have no access to the Live switch.

Bob L

The video viewer options menu (the blue pyramid icon)... one of the video external render options. The video graphics of the computer should be setup as dual monitor extended... that way only the...

The idea here is to sync the video with audio in the multitrack for sound design. The audio on the video itself is not automatically played. To use the base audio from the video file itself, you...