I totally get it, Dale. We've been on the M32 for about 6 weeks now and though I'm usually playing on the platform instead of sitting in the congregation during the music, the thing is killing me. ...
Type: Posts; User: wd5don
I totally get it, Dale. We've been on the M32 for about 6 weeks now and though I'm usually playing on the platform instead of sitting in the congregation during the music, the thing is killing me. ...
I have five (5) ART Tube Opto 8s for sale. These were removed from a church install and are very clean - no mobile use. All have had the Alesis WaveFront chip that gave trouble in some batches...
Our church has, over my strenuous objections, replaced our SAC system from 2009 with a Midas M32. Consequently, we have several TubeOpto 8s and ADA8000s available. Obviously the money they will...
Thanks to all for the responses, it is very much appreciated. And thanks, Butch, for confirming what I was suspecting about a lot problem...I'll get in touch with my supplier (again) about warranty...
Anyone else having clocking issues with recent TubeOpto 8s? I've had multiple failures of a recent batch (purchased 10/13, 4 units so far) with bad clicks and pops when synced to ADAT. Sometimes...
All valid points, Brent, not trying to start a war here. Perhaps the amp in question couldn't quite meet the THD, IM, or even the slew rate requirement with the larger output voltage swing required...
No offense, Brent, but I stand by my original statement. A little math…
For an example, let’s say an amplifier has +/- 40V regulated supply rails. This means that with ideal output devices,...
Also, the maximum output at higher impedances is often limited by the value of the power supply rail(s). Barring a spec error, it's possible that the amplifier simply can't output enough voltage to...
Well, tying Pin 3 to Pin 1 will make half of the output driver circuitry (presuming there's not an output transformer) look into a dead short. It probably won't hurt anything, but I wouldn't...
For unbalanced connections, use Pin 2 of the XLR output as hot, Pin 1 as cold. Don't connect Pin 3 at all unless the equipment has a transformer output, in which case you'll need to tie Pin 3 to Pin...
Actually, single phase is indeed 240V. Each side is 120V to neutral. It could be a single transformer, or the 240V side of a 4-wire, 3-phase delta service.
The 208V shows up in 4-wire, 3-phase...
My experience with 5 GHz vs. 2.4 GHz also bears out your observations. We never had much luck with the higher frequency, despite having a clear line of sight from a second story router (perched on...
Name: Padre Island Baptist Church
Location: Corpus Christi, TX
Congregation Size: 200-250
Nice tip, George, thanks! I don't know how I missed that in the manual. :)
This is really minor, but it would be helpful if a channel template store/recall included both the assigned name and preferably the selected color.
We do the same thing as 905shmick does...the headphone amp is in the rack with the ADAs. Plain old 18-3 unshielded cable (left IEM, right IEM, common) is used to connect the outputs from the...
I recently used these modules (Somo 14D) on a project. They worked out great and sound really good. You can select messages with a very basic pushbutton interface, or if you want to get fancier, you...
In my industry the initial UL and CE certifications are anything but self-policed. The tests are both demanding and extremely expensive, and it can take months to get a listing. They also follow up...
Welcome!
Are you having trouble installing it, or does it just not work after installation? Ours works fine in both 2.2 and 2.5...be sure you have the channel input set to FX Src. Also, the channel's input...
+1 for "always in record." :D
It should also be noted that the original PCI-324 software doesn't support ASIO. You can download an updated version of the console with such support from the MOTU website, though I don't remember...
I, too, had to do a bit of digging into the manual and tinkering to figure out that the top fader was the send level and see exactly what was going on with the aux send/returns. I've actually...
This is where we just purchased ours:
http://www.voltageconverters.com/itemdesc.asp?ic=VC300J
$29.95 + $10 shipping. Seems to be a decent little unit. :)
Connect With Us