Close

Page 3 of 9 FirstFirst 12345 ... LastLast
Results 21 to 30 of 84
  1. #21
    Join Date
    Jun 2004
    Location
    Southern Tablelands, NSW, Australia
    Posts
    1,073

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Hi Bob,

    I don't know what I have done wrong but I cannot get any output from any SAC monitor mixers to my RME other than from the the main SAC mixer. If I load SAC32, it all works ok. I have triple checked the setup and they seem identical. Any thoughts on what I have missed.

    Cheers
    Bruce
    Bruce Callaway
    Broken Knee Studio

  2. #22

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    I just tested here and it seems to be ok on my setup... using an RME... can you check TotalMix and make sure you have selected Preset 1 (usually) for a 1 to 1 assignment of channels... if your main FOH is working ( I assume Out 1+2)... can you try just changing that to Out 2+3) and look at TotalMix to see if the signal has moved to out 2+3... etc...

    Bob L

  3. #23
    Join Date
    Jun 2004
    Location
    Southern Tablelands, NSW, Australia
    Posts
    1,073

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Quote Originally Posted by Bob L View Post
    I just tested here and it seems to be ok on my setup... using an RME... can you check TotalMix and make sure you have selected Preset 1 (usually) for a 1 to 1 assignment of channels... if your main FOH is working ( I assume Out 1+2)... can you try just changing that to Out 2+3) and look at TotalMix to see if the signal has moved to out 2+3... etc...

    Bob L
    I assumed that would be the case Bob, must be a problem at my end. I will keep checking.

    Cheers
    Bruce
    Bruce Callaway
    Broken Knee Studio

  4. #24

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Consider putting the RME TotalMix in DAW mode... which is a 1 to 1 routing.

    Bob L

  5. #25
    Join Date
    Jun 2004
    Location
    Southern Tablelands, NSW, Australia
    Posts
    1,073

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Quote Originally Posted by Bob L View Post
    Consider putting the RME TotalMix in DAW mode... which is a 1 to 1 routing.

    Bob L
    Good advice. Did that plus uninstalled and reinstalled RME drivers/Totalmix and SAC64 but to no avail. I just get no output from the monitor mixes to any output device, main mix no problem. I must have a Windows issue somewhere, go figure.
    Bruce Callaway
    Broken Knee Studio

  6. #26

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Anyone else having this same issue or is their SAC64 able to output to multiple devices. Mine seems to be working here.

    Bob L

  7. #27

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    SAC-Link / SAW-Link
    When I hit the SAC-Link button I can go to SAW but when I hit SAC-Link button, I go to the desktop. Both programs are still operational but I must hit the SAW icon on the Taskbar to go to SAW.
    Mike Bizanovich
    Wheeling, WV

  8. #28
    Join Date
    May 2004
    Location
    Richmond, Kentucky
    Posts
    218

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    I have the same problem but figured it was another "operator error" thing that I would have to track down. Tried several different setups from scratch and imported
    others and still no monitor outputs.
    Lenovo laptop C2D 2.8G 8 G DDR3 ram Profire 2626 with one ADA8000
    SAC 4.5 is working fine ie all monitors good but SAC64 isn't doing monitors. Mains are OK

    Steven Lewis
    Mountain View Recording
    Audio-Video Electronics

  9. #29
    Join Date
    May 2004
    Location
    Richmond, Kentucky
    Posts
    218

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Update to previous post.
    Ok this is strange. I run the mains on 1/2 and the sub on 7/8 of the Profire. Side by side on the Out 1 and Out 2 of the FOH-Main and assigned to 1 and 2 of the output assign section.
    They are both working,
    but 3/4 5/6 9/10 11/12 are not sending any output to the monitors. It shows a signal on the 3/4 Monitor 1 meters but nothing is going to the monitors.
    I can go back and assign the 3/4 as Output 3 on the FOH-Main and it outputs signal to the 3/4 monitor speaker. But resetting it to Monitor 1 and testing
    all the assigns does nothing. I'm thinking it has something to do with the Profire but the same exact setup is working in SAC 4.5.

    Steven Lewis
    Mountain View Recording
    Audio-Video Electronics

  10. #30

    Default Re: SAC (and Plugins) 64 Bit Version Bug Reports

    Quote Originally Posted by Bob L View Post
    Anyone else having this same issue or is their SAC64 able to output to multiple devices. Mine seems to be working here.

    Bob L
    Bob, Just tested. I have outputs on 8 channels of a Behringer ADA8000
    Mike Bizanovich
    Wheeling, WV

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •